distance between nodes in RAM Elelments
Hi,I want to know if RAM Elements has a tool to show distance between nodes like Staad pro.Thanks.
View ArticleParametric Model -Error List
Hi Is there a error list available to show the errors that could occur during parametric modelling and also their diagnosis..thanks..
View Articleautopipe import to staad pro
Hican some one provide a sample model for autopipe that i can try importing within staad pro to see if and how it works.thanks..
View ArticleRSA Mode 1 Period Determination
My question is in two parts. First of all, how does Staad determine where to start the RSA analysis, what determines what the first frequency it looks at is?The second part, is I am trying to work out...
View ArticleSUPPORT REACTION ERROR SHOWN NULL
We are facing a problem in Support reaction output in every node shown 0.00 in following load cases Dead Load,Live Load ,Wind Load,Short circuit & Thermal NodeINPUT FILESTAAD SPACESTART JOB...
View ArticleClik here to view.
after running analysis i am geting this error , what shoud i do ?
After running analysis i am geeting this error , what shoud i do ?
View ArticleHow to provide a support condition for mezzanine beam which is supported by a...
I am designing a roof structure which is about to be supported by a mezzanine platform. The whole platform is supported on a anchor rod at different locations It will be like, there are anchor rods at...
View ArticleClik here to view.
STAAD Connect - Design Parameters Unbraced Length
Good day,My member element in STAAD is only 0.61-m however I want to analyze it at 2.4-m because that's the total length of the cantilever. To do that, I assigned a design parameter LT = 2.4 m and an...
View ArticleRAM Concept Rounding Up Errors
Hi all,Please see below the line transfer dead load text files with three different units (mm, in, and ft). I put these transfer dead loads along the columns’ lengths. Then, I use these text files to...
View ArticleMain 1 Command does not appear to work with CSA S16-14
See title - I'm using 20.07.11.90. Main 1 used to work with older codes.
View ArticleClik here to view.
Crank Bars / Bent up bars Beam design in Staad RCDC ?
Is it possible to design Such Beam with crank / bent up bars in RCDC ? So far i know there is just Curtail bars beam design in Staad RCDC. Please Do Guide me.
View ArticleClik here to view.
I have done a model for a plan. Please check.
I have done a model for a plan. I have attached my plan of the designed building. Please check whether I have done it correctly and give some suggestions for better designs. First and ground floor...
View ArticleRAM Frame Shear Wall Forces Crash
I have an RSS file which crashes every time I try to open the Shear Wall Forces module in RAM Frame. I have used the module before without issue on this project but am trying to use it for the first...
View ArticleWater tank - ***WARNING - INSTABILITY AT JOINT .....
Dear all,This is my first time using Staad and I have tried to model a water tank, After running the analysis, There are some errors about instability at a joint on the wall of water tank. I read some...
View Articlewhy bending moment values are zero when I applied temperature gradient to...
when I applied Temperature Gradient as 25 degrees Celsius to Simply Supported Beam Output Results Shows Only deflection Value of 10.272 mm but bending moment values are shown as 0 can anyone tell me...
View Articlestaad user table §ion wizard
hi i have created channel section using section wizard where i have import the profile from Dxf file. The same section i have also created using user table by defining profile polygon.analysis is...
View Articlemoment release in beam instead of fixed but supports
Dears,I have a frame with 6 main supports( fixed). Earlier i used fixed but supports by releasing lateral forces (Fx & Fy) by giving slotted holes. Now i need to design by giving standard holes in...
View ArticleHow do I model Floating Columns ?
Is there any way to model Floating Columns in Staad Pro ?
View ArticleStaad Pro v8i select series 2 will support windows 7 or not
Staad Pro v8i select series 2 will support windows 7 or not
View Articlehow to extract geometry from staad to autocad through excel VBA
how to extract geometry from staad to autocad through excel VBA
View Article