Story/base shears in modal analysis
I'm running a model with a site specific spectrum. When I compare the dynamic results to the ELF results, the modal story and base shears are 5 to 7 times the ELF story/base shear values. I'm...
View ArticlePost-tensioning Estimate takeoff
Hi There,What is the assumption that RAM concept is using when calculating the PT takeoff weight?In the estimate report is mentions "materials". I'm curious does this include:- Steel block/wedge at...
View ArticleClik here to view.
LIMCON AS 4100
Hi everyone,I am using LIMCON V3.63.2.4 to do a a check for Slotted HSS bolted to gusset plate in AS 4100 code as below:Can anyone explain how we can get these values in highlighted circle like that...
View ArticleWind load not applied properly
Hi Engineers,I have modeled a truss structure , in that model wind load is not applied properly../i have attached model below for reference.../communities.bentley.com/.../01256.std
View ArticleImported columns from dxf not shown at "Base" level in column design module
I imported grids, labels and columns from a dxf file following the instructions. Everything was imported correctly, though some of the grids were split out (this model has both ortho and radial grids)....
View ArticleMAT FOUNDATION IN RAM CONCEPT
Hi everyone. I am fairly new to RAM. I was trying to export my mat foundation from RAM SS to RAM concept. I checked everything to be exported to RAM concept including columns, beams, loads, etc....
View ArticleClik here to view.
Clik here to view.
Allowing a structure to slide in a direction like a roller
I am wanting the end supports to slide in the -x direction instead of put stresses into the beam system. How do I change the staad model to allow for this?
View ArticleRAM SS Frame Beam Axial Load
Hello,I am running my steel design and seismic provisions in the Frame Module and I am getting an odd output for the beam design. I have BRB frames in a K-Brace configuration. When I click view/update...
View ArticleRAM STRUCTURAL SYSTEM
HELLO,I WOULD LIKE TO ASK HOW TO CHECK SOFT STORY, STIFFNESS CHECK AND DRIFT CHECK IN RAM STRUCTURAL SYSTEM.THANK YOU
View ArticleHi, If I buy one Limcon license, are you going to give product support over...
Hi, If I buy one Limcon license, are you going to give product support over the years
View ArticleClik here to view.
Problem in creation of surface mesh
Hello,I am trying to create a surface mesh every time found the a problem. please have a look on attached image.please help me how to do this.
View ArticleClik here to view.
Interaction value for user table channel property is too high
Hi Engineers,I have modeled a canopy in that i have u channel created in user table is used as property../but that property interaction value is too high why???i have attached model...
View ArticleClik here to view.
Grade Beam Design Forces in SFA
I have pile caps modeled on a mat foundation connected by grade beams. Within STAAD Foundation the grade beams are showing 0 forces on them. In the calculation sheet, the grade beams are being designed...
View ArticleMinor changes from floor to floor with typical layout
Hi,I have several similar storeys that have minor changes in exterior geometry and loading from floor to floor. Is there a way to replicate framing from one storey to another and then make the minor...
View ArticleRevit 2019 to ISM to RSS - missing structural components
I have a fairly simple structure (so far it consists of steel beams, joists, girders and columns, and concrete tilt-wall panels) that I'm trying to analyze in Ram Structural System but it seems that a...
View ArticleStaad.pro Connect Edition update 3 + openstaad API + .NET C#
Hi ,i trying to develop custom tool using openstaad + c#. i want know what is reference .dll name and where its located in staad installed path.(specially connect edition)your sample Excel macro is...
View ArticleFlange bracing, rotated W10
I have a built up truss with the top and bottom chords being W10x49. These top and bottom chords are rotated 90deg, so the flanges are on the sides. Can you tell me how i can brace the "top" flange for...
View ArticleComposite deck modeling
Hello,Where can I find some tutorial or guideline for model composite deck, analysis and beam design in STAAD? I tryied find on benltey learn server but I could notThanks in advance
View ArticleProblem in creation of node group
Hello I create a staad pro file and run it normally , but when I create a group of node in my file, it can't not run and "*** ERROR *** ABOVE LINE CONTAINS ERRONEOUS DATA. " appearsRegardsFile without...
View Article