Integrated STAAD and Autopipe
Dear colleaguesWe are attempting to model piping and its structure using integrated STAAD and Autopipe program. The piping in this case is 30" and the model includes thermal expansionBefore this our...
View ArticleHow can i change depth and width of beam to any arbitrary value in OpenSTAAD?
I'm trying to optimize a structure using OpenSTAAD. but i'm not able to figure out how to change the width and depth of flange to any value. help please.Also, what is 'property reference number' in...
View ArticleRAM Concept Load History steps
I am analysing a transfer structure which will support multiple floors above.This will result in a gradual increase in the applied dead and imposed loads as each supported floor is constructed, with...
View ArticleRAM - set up network standards vs local standards
Right now we install RAM out-of-the-box on the user's local computer - not standardization across the network. We had the condition where a user made changes locally that caused a design issue. So my...
View ArticleMetal Formwork
Is there any way to model metal formwork (Bondek, Kingflor, etc) for one-way slabs in RAM Concept?
View ArticleClik here to view.
ERROR WHILE SAVING THE FILE IN STAAD ADVANCED FOUNDATION
When I try to open new file I try to save the file following error is showing. Please provide the solution.
View ArticleNeutral Axis Depth
How can I check neutral axis depth for any given design section in RAM Concept?
View ArticleClik here to view.
User define table
I built up a section under user define table, general. then click compute section properties. error and warning appear indicating the followings **WARNING- TD or TB IS ZERO IN USER TABLE= 1 **ERROR- AY...
View ArticleLimcon V3.63.02.07
Limcon V3.63.02.07 is not available for download in Bentley site for our search (Latest is Version is V3.63.02.06).Please share download link for Limcon V3.63.02.07 which will support for ASIC341...
View ArticleRAM Structural Composite beam design - concrete crushing
In RAM Structural, Steel Beam Module, I have found a number of compositely designed beams seem to actually have invalid designs. The beams appear to be designed and stud numbers chosen but when I...
View ArticleCG in Ram Elements
Hello,I'm wondering how to find the CG of a frame (Including DL) in Ram Elements. I saw the forum on how to find it in STAAD. I was hoping there was also a way to do it in elements?
View ArticleClik here to view.
Problem in Installing Staad.Pro (specifically Connection Client)
Hi!For some reason I had to refresh my Windows 10 notebook. After that I am unable to install Staad.Pro again. It is showing error 2147023293 while trying to install CONNECTION Client 10.00.06.034 (64...
View ArticleShear wall design in staad
i have to design shear wall for my structure by manual calculation , for that i have done analysis in staad but i dont know how to take results from output file , i want axial force, moment and shear...
View ArticleClik here to view.
What is the best way to design a concrete basement wall?
Dear support and colleagues, I have a model with three levels:the first one is an underground level, therefore it is surrounded with concrete wall with lateral earth pressurethe second one is on ground...
View ArticleIS It Possible to stadd pro model for cooling tower with raker columns.If...
Actually I made a model in the cooling tower.I Have a doubt in keeping raker columns to the cooling tower down at the bottom.
View ArticleIn Applying Loads in staad pro.........! it is necessory to apply load...
I am new in staad pro so please answer this question in very easy language....! It is necessary to apply load combinations if yes than what is the correct procedure to combine them..........?
View ArticleTimber Code Check is not working
I have materials set in a truss model as SPFR_SS_2x4, all from the section database within STAAD. When I run a "Code AITC" check in the command file editor, an error appears "Above line IGNORED! Check...
View ArticleExporting linked design members from Microstran to ISM
I am trying to create or update an ISM repository from a microstran model. As soon as I create 'linked' design members then when I update or create an ISM repository it fails with the following...
View Article