DOES STAAD CALCULATE SEISMIC FORCE IN VERTICAL DIRECTION (OTHER THAN TWO...
As per revised I S 1893 ( part 1) : 2016 clause 6.33 it is required to consider all three direction X Y & Z seismic force combinationhow these three seismic forces in X ,Y & Z...
View ArticleResult of Cutoff mode in not showing in output file of staad version build...
Result of Cutoff mode in not showing in output file of staad version build 21.00.01.12
View ArticleColumn design using moment magnification
Good day,I performed a concrete design in STAAD Pro using the moment magnification method, however, there seems to be an error as the Slenderness ratio (Klu/r) reported by STAAD is much smaller than...
View ArticleClik here to view.
RAM Frame Reactions for an "Elevated Building"
I am designing the top level of a structure. I modeled a dummy structure below to ensure I was getting the correct wind loads. I need to get the reactions from my top level on the structure below....
View ArticleClik here to view.
Steel Deck Thickness Unusual Results
(Please visit the site to view this file)I have a model where I modeled the steel roof deck (with plates) using the equivalent thickness of deck based on the ratio of equivalent shear stiffness to the...
View ArticleSTAAD FOUNDATION ADVANCED v08.03.00.20: Error one way shear and puching shear...
Hi,We have just running Staad foundation advanced v 08.03.00.30, but there are many errors with on way shear and punching shear check of footing according to Eurocode 2.One way shear check error in...
View ArticleBox section with different flange and web thickness
Dear Moderator,I want to design steel box section with different flange and web thickness as per AISC 316.Create user table doesn't allow in "Tube" definition properties, different thickness? If i do...
View ArticleMOVING LOAD - VEHICLE DEFINITION - MAX . NO. OF AXLE
Dear friends,I am facing with the moving load with a lot of axles (32). This is a results of 3 lining up cranes.The problem is that I can only define the vehicle with max. of 19 axles. Can any one tell...
View Article'Tension Only' braces with 'Perform Analysis + Change' command analysis...
I am designing a partially cladded building with Tension Only braces. I have put Perform Analysis + Change command after each Seismic case as i wish to do IBC/UBC load generation.I have figured that...
View ArticleProblems in the latest STAAD Connect ed
STAAD pro comes with many bugs that not exist in previous version in every update; something wrong needs to be investigated. Here is the issue I found in this version. (Windows 10 64x sys)1- When...
View ArticleCODE AISC Unified 2010
When entering loads using CODE AISC Unified 2010 do I multiply my loads by the load factors before I enter them into STAAD or does STAAD do that?
View ArticleView design calculation for code checks
What is the procedure for viewing the design calculation for physical members. When I analyze a steel structure and do a code check to CSA S16, I get a message that design output is not available for...
View ArticleClik here to view.
Unable to setting up the system for RCDC 6.3
Hi,I have installed RCDC 6.3 for my window 8.1 machine 64 bit. After installation I knew that RCDC will do setup at the first time I open the RCDC, on the previous version of RCDC I did not received...
View ArticleHow to create section data base ?
Hi, We want to compile the data base by mix of Indian (Channels & Angles), Jindal (UB, NPB & UC) and TATA Structura (RHS, CHS & SHS) sections. Actually we are using "select" command and...
View ArticleClik here to view.
STAAD(X).Tower Eurocode development release date
Does anyone know when the STAAD(X).Tower Eurocode development release date is? I was advised January 2018 on a previous post but I am now wondering what the specific date will be.
View ArticleClik here to view.
RAM Concept Crash
Hi all,Everytime I logged into Ram concept 06.04.00.06, it kept going crashed like this. Could you guys help me to solve this problem?I already uninstalled Dell backup and recovery and disabled RSS...
View ArticleClik here to view.
STAAD.Pro Connect Edition
I trying to install STAAD Pro Connect Edition, but it is giving error. please any one help
View ArticleClik here to view.
STAAD RCDC NOT RUNNING
Hi All,I installed STAAD RCDC on my system and after 7 days, it stopped working. The licence is activated but I cannot open any new project or sample projects. I made attempt to uninstall and...
View ArticleDIFFERENCE AMONG AREA ,PLATE & FLOOR LOAD IN STAAD.PRO?
I AM NEW IN STAAD.PRO, SO I AM CONFUSED WHICH LOAD SHOULD I ASSIGN IN A PLATE ELEMENT??
View Article