Plate Element Results In Staad Pro.
Hi,Can you please tell me what are Min and Max results of plate element(please see attached image below)Thank you
View ArticleSTAAD FOUNDATION ADVANCED
1) When I view the base pressure contour lines, I see base pressure values such as -14.4 E9 ksf which does not make sense. Also, these values (displayed on the model screen) are too different from the...
View ArticleIssues with STAAD.Pro CONNECT Edition.
Firstly, I like the new look to STAAD and was happy to see some semblance of software development for the cost of a subscription. Hopefully this new interface will also be rolled out with STAAD...
View ArticleRam Elements Effective Length Factors
See the column and member restraints and fixities below. I have my K33 and K22 values both set to "0" and the K value type set to "Recommended". The Ram Elements help section says the following:"For...
View ArticleShrinkage strain in Ram concept according to AS3600
How to calculate the shrinkage strain in Ram concept according to AS3600, thank you
View ArticleDynamic Analysis Equation
Can I extract Stiffenes Matrix Equation and Mass Matrix Equation from Model that I have made?
View ArticleOpenSTAAD Function "Output.GetMinMaxBendingMoment"
Please help...OpenSTAAD Function "Output.GetMinMaxBendingMoment" returns 0 values while successfully executed (returned "true" value). I double checked the member no, strDir = "MZ" and lLoadCase; all...
View ArticleRCDC for ACI code on rebar strength fy = grade 40 or grade 33
Dear ALLHope this is the correct forum i log in. regarding for Staad RCDC (Aci code), is it possible to ADD rebar strength = grade 33 to 40 or 220 to 275 Mpa? as noted it allows only from Fe410 to Fe...
View ArticleSTAAD Composite Steel Beam Error
I am trying to analyze a composite steel beam in STAAD and keep getting an error that says design of section for member is not supported. Here is my input. STAAD SPACESTART JOB INFORMATIONENGINEER...
View ArticleSection Wizard - Shear center of built-up column
Can the section wizard be used to determine the shear center of a built up section? I am evaluating an existing structure that has built-up columns (2 channels with a continuous plate on one side and...
View ArticleHow can I get the RAM Connection User's Manual in Spanish?
Good AfternoonHow can I get the RAM Connection User's Manual in Spanish?I need the RAM Connection User's Manual in SpanishRegard,Pablo Mata
View ArticleGENERATE Command
When the GENERATE command was introduced in SELECTseries 4, the manual stated that it was to be used in conjunction with design codes ASME NF, AISC 360 05/10 for appropriate sign/direction for ABS/SRSS...
View ArticleGusset plate of bridge connection
Dear Sir,Can I made model of bridge connection with splice plate and gusset plate as in figure 1.and all with gusset plate as in figure 2. (see my attchment) with RAM Connection? Thanks a...
View ArticleRam connections in Staad Pro
How does one create and move custom Ram connection templates into the Staad Pro interface?I found an article on the Bentley site that describes adding to the connnections.ini file, but the end of the...
View ArticleCheckcode for back-to-back channel section
In our last version of Staad V8i, serie 6, version 20.07.11.82, we can't make a checkcode for back-to-back channel section. In older version, we used to make checkcode for these section without any...
View ArticleQuestion about the signs of Moment
Dears,Reference to below example, the moment is positive reached the maximum 2000 and then go down to -1600.But According to STAAD, it is on the opposite direction.Can someone kindly explain the reason?
View ArticleStep in Slab in RAM Concept
I'm looking at a podium slab with a 6" step in the top of slab (constant soffit across the step) for a topping slab in a courtyard area. We added a 75psf area DL in the 6" recessed area to account for...
View ArticleRAM FRAME STORY DISPLACEMENTS
In RAM Frame, are the story displacements in the story displacement report all relative to the ground floor or are they relative to the floor below them? Thanks.
View ArticleSTAAD Cone Plate Model
Is there an easy way to create a cone shaped plate in STAAD? The structure wizard has a spherical shape, but I don't see an easy way to make a cone.
View Article