WELD SIZE IN "MM"
Dear allI am using RAM Connections for connection design. In SI system weld size is still displays weld size times 1/16 of an inch in all type of conection. But i need to exter value in using...
View ArticleLink Tekla with Limcon
HelloI have one question in structure detailing workflow between bentley Limcon with Tekla Structures, the connection can transfer from Tekla to Limcon and reverse ?Thanks All
View Articlewarning
Hi Forum,I am designing shear wall. While defining wall panel and run the staad it shows "WARNING- One or more lines are too long and will be split into 2 lines. Please suggest me a...
View ArticleREGARDING WELD SIZE IN RAM CONNECTIONS
Dear all I am using RAM Connections for connection design. In SI system weld size is still displayed in 1/16 of an inch in all type of connection. But I need to enter value in mm and not using...
View ArticleRange of Wind loads
I have provided all the configurations. But after all it is saying that my structure is not in the range of wind load.Attached is my Staad editor file. Please help me with this.STAAD SPACESTART JOB...
View Articlesingle pile
Good evening,I am designing pile cap using Staad foundation. I have imported staad file from staad pro. Pile capacity is more than thousand and my support reaction is only around 300. Still I am not...
View ArticleRange of wind loads
I have provided wind loads for a chimney. I am unable to give loads to the chimney. Please tell me a way of doing it. Here the STAAD editor file.STAAD SPACESTART JOB INFORMATIONENGINEER DATE...
View ArticleClik here to view.
RAM Concept - Lateral Self Equilibrium - user defined lateral nodal loads
In the RAM Concept Lateral Self Equilibrium [TN] discussion, at the very bottom of the page, there is a note that says, Note: Ram Structural System lateral loads will generally be exported to Ram...
View ArticleRAM Concept slab on grade tutorial
Is there any tutorial for ram concept that shows steps to design slab on grade?
View ArticleForce units revert upon opening new session
Good afternoon,Is there a way to set the output Force Units to be the same upon opening each new session of STAAD.Pro? I am having to change the units each time I open the file if I need to print...
View ArticleI am getting shape of building like while buckling analysis, Is it write or I...
I am getting shape of building like while buckling analysis, Is it write or I am doing something wrong???? Please helpSTAAD SPACESTART JOB INFORMATIONENGINEER DATE 08-Apr-16END JOB INFORMATIONINPUT...
View ArticleSTAAD.Pro ERROR . MEMB OR ELEM NO 0 DOES NOT EXIST.
Our StaadPro Series 6 Version 20.07.11.50 gives us an Output error as follows which we cannot explain: It did not happen in StaadPro Series 6 Version 20.07.11.33***STAAD.Pro ERROR . MEMB OR ELEM NO 0...
View ArticleTension Only Load Cases Fail to Converge
When I run the RAM Frame analysis, I get an error that says "Warning(s) found during analysis. During iterative analysis with tension-only members, some of the load cases failed to converge. Please see...
View ArticleReference loads for seismic mass in response spectrum analysis
Hello, I am performing response spectrum analysis in three directions on a large model in STAAD (v8i version 20.07.11.50) using the "generic" method as discussed in Section 5.32.10.1.1 of the Help...
View ArticleNeed to know the total amount of each type of beam used
Hi, I created a structure using two types of beams W16X40 and W21X62 and I need to know how many beams were used for each type of beamI know that the total amount of beams used are 2009 but I need to...
View Article3 storey RCC structure
Can anyone pls upload a staad file (.std) of a conventional g+3 rcc framed structure. It would be of great use in my project. Thank you
View ArticleI want to design a profiled steel sheet and concrete core composite wall....
I want to design a composite wall which has two profiled steel sheet surrounding a concrete core and i am not sure which of the bentley software would make this deign possible.
View ArticleIs it effective to use plates for designing slabs?
Dear members,I want to discuss whether a 4-noded plate is sufficient to represent as a slab or proper meshing along with the supporting beams is required to distribute the load uniformly over the...
View ArticleWarning message Out of plane loads applied on the plane structure
Hi friends, I am getting a warning message .Truss analysis . Please help meSTAAD PLANESTART JOB INFORMATIONENGINEER DATE 21-Apr-16END JOB INFORMATIONINPUT WIDTH 79UNIT METER KNJOINT COORDINATES1 0 0 0;...
View ArticleClik here to view.
Assigning Imposed Lateral Loads in RAM SS for Use in RAM Concept
I am working on the design of a concrete substructure (elevated slabs, concrete columns, basement walls, and foundation elements), while a collaborating firm is designing the steel superstructure...
View Article